Good day members of Diyhub community, I'm so excited to be with you all again and also to post here. Today I decided on making an Electrical⚡ Tricycle (Keke) and the driver as well, it really took a lot of time but it was so nice after the construction. So here are the materials I used in the construction MATERIALS
1). Carton 2). Scissors ✂️ 3). Super glue (3) 4). Tiny electric ⚡ wire's 5). Tiny Bulbs 💡(2) 6). Tiger 🐯 battery 🔋 (3) 7). Plastic Mineral covers (4) 8). Water colour 9). Yellow plaster 10). Pencil ✏️, sharpener, and eraser 11). Two sticks of broom 🧹 STEPS AND METHODS OF PRODUCTION
1). STEP ONE: Cut out a piece carton and then use the pencil ✏️ to draw and carve out the two side's of the Tricycle and then cut it out with the Scissors ✂️ as you can see in the picture below 👇.
2). STEP TWO: Cut out another small peice of carton and then use the pencil ✏️ to draw a corner for the front mirror 🪞 and then use the scissors ✂️ to cut it.
3). STEP THREE: Now use the super glue to gum the mirror 🪞 that you have cut out with the two body of the Tricycle .
4). STEP FOUR: Cut out a carton for the roof of the Tricycle and then use the super glue to gum it with the Tricycle.
5). STEP FIVE: Now cut out a peice of carton for the front case of the Tricycle and then use a super glue to gum it to the front of the Tricycle.
6). STEP SIX: It is now time to fix and connect the front tyre with the stick of broom and plastic Mineral covers and then curve a small carton for putting the tyre inside, after that by use a super glue to gum it to the Tricycle.
7). STEP SEVEN: Use a small carton to form an area for the back tyre's and then gum it in the arranged tyre section.
8). STEP EIGHT: Now connect the Tiny electric ⚡ wires and Tiny Bulbs 💡 together, and then make an opening in the Tricycle for the eyes, then fix the bulbs 💡 in the openings
9). STEP NINE: Fix the back tyre's by using some sticks of broom and plastic Mineral covers and then connect it to the Tricycle.
10). STEP TEN: Use a scissors ✂️ to cut out a peice of carton for the front desk and also the stirring of the Tricycle and then use the super glue to gum both of them inside the Tricycle.
11). STEP ELEVEN: Use a peice of carton to form the front seat 💺 for the driver and also form the front casing, then use a super glue to gum the both of them inside the Tricycle.
12). STEP TWELVE: Cut out another piece of carton to form the up foam chair of the front seat and also cut out a small carton for the back chair of the Tricycle and after everything you can use your super glue to gum the two of them inside the Tricycle
13). STEP THIRTEEN: Form the driver using a small peice of carton and then construct a fine design which you would put in front of the Tricycle closet to the eyes 👀 of the Tricycle.
14). STEP FOURTEEN: Now use a carton to form the back side of the Tricycle and make an opening for bringing out the Tiny electric ⚡ wire's, and then use the super glue to gum the back side together with the Tricycle
15). STEP FIFTEEN: Cut out a small part of carton for the closing of the under of the Tricycle and then ues the yellow plaster for wrapping it well so that i would not fall out.
16). STEP SIXTEEN: Arrange and wrap 🌯 your Tiger 🐯 battery 🔋 (3) and then connect it with the Tiny electric ⚡ wire's and bulbs 💡then wrap 🌯 it well with the yellow plaster in other to attract energy to the eyes 👀 of the Tricycle.
17). STEP SEVENTEEN: The last step for me was to draw and colour the Hive Logo using a pencil ✏️ and Red colour from my water colour.
And after everything the electrical ⚡ tricycle with the driver was now ready to use for work
All pictures were taken with my Tecno spark 40 phone 📱
Thank you all for stopping by my blog today, i really appreciate it.